Johnson 09-802B Impeller Kit for F9 Pumps (Neoprene)

Description

The genuine Johnson neoprene flexible impeller is suitable for general water-pumping duties such as engine cooling, water transfer, wash down and bilge water pumping purposes. The Johnson flexible pump impeller is designed to be installed to some of the F9 range of Johnson Pumps which suits the impeller dimensions listed below, including:

- F9B-3, F9B-303, F9B-3000 (TSS/VF), F9B-3007, F9B-3020, F9B-3027, F9B-3030 and F9B-3037 pump models: 10-13026-1, 10-13026-2, 10-13026-3, 10-13026-7, 10-13026-8, 10-13026-9, 10-13177-01, 10-13225-01, 10-22346-1 & 10-22346-2.

- F9B-5 pump models: 10-22362-.

- F9B-9, F9B-900 and F9B-903 pump models: 10-13064-1, 10-13064-2, 10-13145-01, 10-24072-1, 10-24090-1, 10-24090-2, 10-24239-1 & 10-24239-2.

- M.A.N. pumps 50.06500-7011 & 50.06500-7012.

The Johnson flexible pump impeller has nine blades and is supplied complete with 2 x lubrication gel and instruction manual to aid installation of the impeller into the flexible impeller pump.

The Johnson 09-802B can be used to replace the Jabsco 6760-0001 Europe and USA flexible impeller.

It is highly recommended to make sure you use an original pump impeller for your flexible impeller pump as this will ensure that the quality complies with the performance and dimension requirements for each pump type. Johnson Pump impellers are manufactured in strict compliance with the pump specifications set by the engine manufacturers.

The impeller fits the following engines as standard:

- Caterpillar

- MAN D2540MLE, D2542LE, D2840LXE/LE401, D2840LXE/LE401/403, D2842LE, D2842LE401/02/06/03/08, D2842LYE/LZE, D2848LE/LXE & D2848LXE/LE/LE401/403

- Nanni D2840LE, D2842LE, D2842LXE, D2842LYE, D2848LE, D2866LE, D2866TE, 2100 & 2100T

- Schwarting S424A & S424LA

How to remove an old impeller:

Remove the impeller with slip joint pliers or a Johnson Pump Impuller (Part Number 09-800)

How to fit a new impeller:

Lubricate the shaft and the inside of the pump body and the end cover. Use Johnson Pump Lubrication to help develop prime and prevent damage from dry-running the pump at initial start-up. Mount the impeller by making a pushing and twisting movement in the rotating direction. Lubricated impellers should not be stored for extended periods of time. The engine should be run after installation of a new impeller to wash out the lubrication. These recommendations apply to any service work on the pump and its components that require the use of lubrication inside the pump for assembly and start-up.

Warning! Do not use any petroleum-based products to lubricate the inside of the pump. Only use Johnson Pump Lubrication. Other products can damage the impeller which will damage the pump and lead to engine failure. Do not run the impeller without water or lubricant; this can cause engine failure or a fire.

1. A vacuum is created as the flexible impeller vanes straighten upon leaving the cam drawing liquid into the pump.

2. The rotating impeller carries liquid from the inlet to the outlet port. As a consequence of their design flexible impeller pumps can pass fairly large solids.

3. When the flexible impeller vanes regain contact with the cam they bend and the liquid is discharged from the pump in a uniform flow. Liquids can be pumped in the opposite direction by reversing the rotation of the pump.